The drivetrain decides the kit, not the trim badge
H&R builds two distinct Sport Spring sets for the Tesla Model 3, and the split follows drivetrain rather than trim name. The AWD kit is listed for 2018–2022 Long Range and Performance cars; the RWD kit is listed for 2019–2022 Standard Range and Standard Range+ cars. Each set includes four springs and is designed for cars without air suspension.
That means the first question isn't "which spring is better" — it's "which car do I actually have?" Get that wrong and the springs won't suit the car regardless of how they perform on the right application.
The two H&R Model 3 fitments side by side
- H&R 2018+ Tesla Model 3 Long Range (AWD) Performance Sport Spring (No Air Suspension): Listed for 2018–2022 Model 3 Long Range (AWD) and Performance, with approximate front and rear lowering of 1.2". This is the kit for dual-motor cars; the 1.2" figures give you a realistic expectation of the drop before you commit.

H&R 2018+ Tesla Model 3 Long Range (AWD) Performance Sport Spring (No Air Suspension) - H&R 2019-2021 Tesla Model 3 Standard Range/Standard Range+ (RWD) Sport Spring (No Air Suspension): Listed for 2019–2022 Model 3 Standard Range and Standard Range+ (RWD), with approximate front and rear lowering of 1.2". This is the RWD-specific kit; the matching 1.2" drop means the choice between kits is about fitment, not ride height.

H&R 2019-2021 Tesla Model 3 Standard Range/Standard Range+ (RWD) Sport Spring (No Air Suspension)
Why the AWD and RWD kits are not interchangeable
The two listings carry explicit, opposite compatibility warnings. The AWD kit is marked not compatible with rear-motor-only (RWD) models, and the RWD kit is marked not compatible with dual-motor (AWD) models. Those warnings are the clearest signal in the supplied information: the spring rates and fit are application-specific, so cross-fitting isn't a shortcut.
The RWD kit carries an additional restriction that matters for later cars: it is not compatible with LFP battery cars (the China-made battery). If your Standard Range or Standard Range+ has an LFP pack, the supplied information rules this kit out. The AWD listing does not carry an equivalent LFP note in the supplied evidence, so don't assume the same restriction applies — check your own car's battery type before ordering either kit.
Fitment checks to settle before you order
- Confirm your drivetrain: Dual-motor (Long Range or Performance) points to the AWD kit; rear-motor-only (Standard Range or Standard Range+) points to the RWD kit. The listings treat these as hard boundaries, not preferences.
- Check your model year against the listing: The AWD kit is listed for 2018–2022 cars; the RWD kit for 2019–2022 cars. A car outside those windows isn't covered by the supplied fitment information.
- Identify your battery if you have a Standard Range car: The RWD kit is explicitly not compatible with LFP battery cars (China-made battery). If you're unsure which pack your car has, confirm it before ordering.
- Rule out air suspension: Both listings describe springs for cars without air suspension. If your car has air suspension, neither kit is the right starting point.
What the springs are designed to change
Both kits share the same engineering story: a moderately lower ride height, a lower center of gravity, reduced body roll, and more responsive handling. H&R also states that the resulting lower wind resistance helps increase energy efficiency. The springs are progressive where the application allows, are made in Germany at an ISO 9001 certified facility, and are shot-peened to increase life by more than 200%, with each spring 100% tested before leaving the factory.
The honest trade-off is that this is a ride-height modification, not a complete suspension overhaul. You're changing springs on the factory dampers, so the result is a lower car with the handling character H&R engineered for that application — not a track setup.
Shared engineering behind both Model 3 kits
- H&R 2018+ Tesla Model 3 Long Range (AWD) Performance Sport Spring (No Air Suspension): Progressive springs, shot-peened to increase life by more than 200%, and 100% tested at H&R's ISO 9001 certified facility in Germany. These are the durability and quality claims that apply to the AWD kit — useful when comparing against unbranded springs.
- H&R 2019-2021 Tesla Model 3 Standard Range/Standard Range+ (RWD) Sport Spring (No Air Suspension): Progressive springs, shot-peened to increase life by more than 200%, and 100% tested at H&R's ISO 9001 certified facility in Germany. The RWD kit carries the same manufacturing claims, so the decision between kits stays about fitment rather than build quality.
Installation and alignment: what the listings require
H&R states that its springs and suspensions should be installed by professional suspension mechanics only, and recommends contacting local aftermarket installers with Tesla experience. The listings also say you should measure ride height before and after installation, and that alignment should be checked after any ride-height modification, following the factory service manual to keep alignment as close to factory specifications as possible.
On spring orientation, the guidance is to match the shape of the stock spring: if the spring is the same on both sides and fits either direction, install it with the closer coils up; if one end is smaller, match the OEM factory-installed orientation. Front springs are marked "VA" or "(F)" and rear springs "HA" or "(R)". The listings do not confirm whether bumpstop trimming is required — that would only be noted on the H&R Technical Information sheet or inserted sheets, so check those before the install.
Price, shipping, and the practical decision
At catalog prices, the AWD kit is listed at USD 280.76 (comparison price USD 389.95) and the RWD kit at USD 429.97 (comparison price USD 589.00). Both usually ship the next business day and are available for international delivery. The price gap doesn't buy a different spring design — it reflects the two applications, so let fitment decide, not price.
If you have a dual-motor 2018–2022 Model 3, the AWD kit is the match. If you have a rear-motor 2019–2022 Standard Range or Standard Range+ and it isn't an LFP battery car, the RWD kit is the match. If your car falls outside those windows, or you can't confirm the battery type on a Standard Range car, the supplied information isn't enough to confirm fitment — verify with H&R using the part numbers on the box and springs before ordering.



